Discussion:
Evaluate VP9 Hardware accelerated encode/decode on KabyLake
(too old to reply)
Vijayaraghavan, Vasavee
2016-11-29 03:45:18 UTC
Permalink
Hi all,

I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get started to run hardware accelerated encode/decode tests on KabyLake? I am targeting to run the tests on Linux OS.

Best Regards,
Vasavee
Xiang, Haihao
2016-11-29 04:15:49 UTC
Permalink
Hi Vasavee,

You can run a software using VA-API to evaluate VP9 hardware
accelerated encode/decode, suc as:

libyami:
https://github.com/01org/libyami (core) 
https://github.com/01org/libyami-utils (utilities based on libyami)

gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html

or a FFmpeg/Libav based player which enables HW accelerated decode.

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
 
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on
KabyLake.
Can someone give me useful pointers as in where I can get started to
run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
 
Best Regards,
Vasavee
 
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Vijayaraghavan, Vasavee
2016-11-29 07:56:50 UTC
Permalink
Sorry, didn’t realize I had to reply all. Reposting my message again:

Hi Haihao,

Thank you for your response.
I am not sure if I have to use a specific software for my tests, but looking a bit about the below three options (ffmpeg, gstreamer and libyami) and assuming I go with libyami, do I have to:

1. Simply Follow the build procedure given here: https://github.com/01org/libyami/wiki/Build after installing the specific Linux OS

(Or)

2. Do I have to build the entire graphics software stack after installing the Linux OS including:

Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3

as mentioned in https://01.org/linuxgraphics/downloads/2016q3-intel-graphics-stack-release

-Best Regards,
Vasavee

-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
To: Vijayaraghavan, Vasavee <***@intel.com>; ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake


Hi Vasavee,

You can run a software using VA-API to evaluate VP9 hardware accelerated encode/decode, suc as:

libyami:
https://github.com/01org/libyami (core) https://github.com/01org/libyami-utils (utilities based on libyami)

gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html

or a FFmpeg/Libav based player which enables HW accelerated decode.

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
 
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get started to
run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
 
Best Regards,
Vasavee
 
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Xiang, Haihao
2016-11-29 08:11:57 UTC
Permalink
1. Linux kernel

It would be better to install a recent stable kernel or rc kernel. The
kernel in the specific Linux OS might not support Kabylake.

2. Mesa/Cairo 

It is not needed.

3. Xorg / xf86-video-intel

It is not needed if you won't playback a video, otherwise you should
check xf86-video-intel supports Kabylake or not. Usually you needn't
update Xorg. 

4. libdrm

libdrm in the specific Linux OS might not support Kabylake, so it would
be better to install a recent version of libdrm.

5. libva/libva-intel-driver

The latest version is 1.7.3

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests, but
looking a bit about the below three options (ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://github.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-intel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01org/liby
ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
 
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on
KabyLake.
Can someone give me useful pointers as in where I can get started to
run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
 
Best Regards,
Vasavee
 
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Vijayaraghavan, Vasavee
2016-12-07 22:24:01 UTC
Permalink
Hi Haihao,

I am trying to build the intel graphics stack on Ubuntu 16.10 with:
-linux kernel version 4.8.0 (default kernel that comes with Ubuntu 16.10)
-libdrm version 2.4.68
-libva version 1.7.3

I am having trouble upgrading the libva-intel-driver-1.7.3.
I have error while trying to compile it (I used this for configuring: ./configure --prefix=/usr --exec-prefix=/)
Error below:
***@test-MS-B142:~/Downloads/libva-intel-driver-1.7.3$ make
Making all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
GEN intel_version.h
make all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
GEN frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1

Output of vainfo:
libva info: VA-API version 0.39.2
libva info: va_getDriverName() returns 0
libva info: Trying to open /usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
libva info: Found init function __vaDriverInit_0_39
libva info: va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
VAProfileMPEG2Simple : VAEntrypointVLD
VAProfileMPEG2Simple : VAEntrypointEncSlice
VAProfileMPEG2Main : VAEntrypointVLD
VAProfileMPEG2Main : VAEntrypointEncSlice
VAProfileH264ConstrainedBaseline: VAEntrypointVLD
VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
VAProfileH264Main : VAEntrypointVLD
VAProfileH264Main : VAEntrypointEncSlice
VAProfileH264High : VAEntrypointVLD
VAProfileH264High : VAEntrypointEncSlice
VAProfileH264MultiviewHigh : VAEntrypointVLD
VAProfileH264MultiviewHigh : VAEntrypointEncSlice
VAProfileH264StereoHigh : VAEntrypointVLD
VAProfileH264StereoHigh : VAEntrypointEncSlice
VAProfileVC1Simple : VAEntrypointVLD
VAProfileVC1Main : VAEntrypointVLD
VAProfileVC1Advanced : VAEntrypointVLD
VAProfileNone : VAEntrypointVideoProc
VAProfileJPEGBaseline : VAEntrypointVLD
VAProfileJPEGBaseline : VAEntrypointEncPicture
VAProfileVP8Version0_3 : VAEntrypointVLD
VAProfileVP8Version0_3 : VAEntrypointEncSlice
VAProfileHEVCMain : VAEntrypointVLD
VAProfileHEVCMain : VAEntrypointEncSlice
VAProfileHEVCMain10 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointEncSlice
VAProfileVP9Profile2 : VAEntrypointVLD

-Thanks
Vasavee

-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
To: Vijayaraghavan, Vasavee <***@intel.com>; ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake


1. Linux kernel

It would be better to install a recent stable kernel or rc kernel. The kernel in the specific Linux OS might not support Kabylake.

2. Mesa/Cairo 

It is not needed.

3. Xorg / xf86-video-intel

It is not needed if you won't playback a video, otherwise you should check xf86-video-intel supports Kabylake or not. Usually you needn't update Xorg. 

4. libdrm

libdrm in the specific Linux OS might not support Kabylake, so it would be better to install a recent version of libdrm.

5. libva/libva-intel-driver

The latest version is 1.7.3

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests, but
looking a bit about the below three options (ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://github.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-intel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01org/liby
ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
 
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on
KabyLake.
Can someone give me useful pointers as in where I can get started to
run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
 
Best Regards,
Vasavee
 
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Charles, Daniel
2016-12-07 23:36:02 UTC
Permalink
Hello Vasavee,

Is your user allowed to write files on the --prefix=/usr and the
--exec-prefix=/ directories?

If you want to install it on the default place you don't need to specify those
--
Daniel.

On Wed, Dec 7, 2016 at 2:24 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version 4.8.0 (default kernel that comes with Ubuntu 16.10)
-libdrm version 2.4.68
-libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
I have error while trying to compile it (I used this for configuring: ./configure --prefix=/usr --exec-prefix=/)
Making all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
GEN intel_version.h
make all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
GEN frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
libva info: VA-API version 0.39.2
libva info: va_getDriverName() returns 0
libva info: Trying to open /usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
libva info: Found init function __vaDriverInit_0_39
libva info: va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
VAProfileMPEG2Simple : VAEntrypointVLD
VAProfileMPEG2Simple : VAEntrypointEncSlice
VAProfileMPEG2Main : VAEntrypointVLD
VAProfileMPEG2Main : VAEntrypointEncSlice
VAProfileH264ConstrainedBaseline: VAEntrypointVLD
VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
VAProfileH264Main : VAEntrypointVLD
VAProfileH264Main : VAEntrypointEncSlice
VAProfileH264High : VAEntrypointVLD
VAProfileH264High : VAEntrypointEncSlice
VAProfileH264MultiviewHigh : VAEntrypointVLD
VAProfileH264MultiviewHigh : VAEntrypointEncSlice
VAProfileH264StereoHigh : VAEntrypointVLD
VAProfileH264StereoHigh : VAEntrypointEncSlice
VAProfileVC1Simple : VAEntrypointVLD
VAProfileVC1Main : VAEntrypointVLD
VAProfileVC1Advanced : VAEntrypointVLD
VAProfileNone : VAEntrypointVideoProc
VAProfileJPEGBaseline : VAEntrypointVLD
VAProfileJPEGBaseline : VAEntrypointEncPicture
VAProfileVP8Version0_3 : VAEntrypointVLD
VAProfileVP8Version0_3 : VAEntrypointEncSlice
VAProfileHEVCMain : VAEntrypointVLD
VAProfileHEVCMain : VAEntrypointEncSlice
VAProfileHEVCMain10 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointEncSlice
VAProfileVP9Profile2 : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel. The kernel in the specific Linux OS might not support Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you should check xf86-video-intel supports Kabylake or not. Usually you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests, but
looking a bit about the below three options (ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://github.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-intel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01org/liby
ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get started to
run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Vijayaraghavan, Vasavee
2016-12-08 01:07:11 UTC
Permalink
Hi Daniel.
I believe so, I used this configuration because my libdrm doesn’t build if I use the default config options.

-Thanks
Vasavee

-----Original Message-----
From: Charles, Daniel [mailto:***@intel.com]
Sent: Wednesday, December 7, 2016 3:36 PM
To: Vijayaraghavan, Vasavee <***@intel.com>
Cc: Xiang, Haihao <***@intel.com>; ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake

Hello Vasavee,

Is your user allowed to write files on the --prefix=/usr and the --exec-prefix=/ directories?

If you want to install it on the default place you don't need to specify those
--
Daniel.
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version 4.8.0 (default kernel that comes with Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
GEN intel_version.h
make all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
GEN frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
libva info: VA-API version 0.39.2
libva info: va_getDriverName() returns 0 libva info: Trying to open
/usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
VAProfileMPEG2Simple : VAEntrypointVLD
VAProfileMPEG2Simple : VAEntrypointEncSlice
VAProfileMPEG2Main : VAEntrypointVLD
VAProfileMPEG2Main : VAEntrypointEncSlice
VAProfileH264ConstrainedBaseline: VAEntrypointVLD
VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
VAProfileH264Main : VAEntrypointVLD
VAProfileH264Main : VAEntrypointEncSlice
VAProfileH264High : VAEntrypointVLD
VAProfileH264High : VAEntrypointEncSlice
VAProfileH264MultiviewHigh : VAEntrypointVLD
VAProfileH264MultiviewHigh : VAEntrypointEncSlice
VAProfileH264StereoHigh : VAEntrypointVLD
VAProfileH264StereoHigh : VAEntrypointEncSlice
VAProfileVC1Simple : VAEntrypointVLD
VAProfileVC1Main : VAEntrypointVLD
VAProfileVC1Advanced : VAEntrypointVLD
VAProfileNone : VAEntrypointVideoProc
VAProfileJPEGBaseline : VAEntrypointVLD
VAProfileJPEGBaseline : VAEntrypointEncPicture
VAProfileVP8Version0_3 : VAEntrypointVLD
VAProfileVP8Version0_3 : VAEntrypointEncSlice
VAProfileHEVCMain : VAEntrypointVLD
VAProfileHEVCMain : VAEntrypointEncSlice
VAProfileHEVCMain10 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointEncSlice
VAProfileVP9Profile2 : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel. The kernel in the specific Linux OS might not support Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you should check xf86-video-intel supports Kabylake or not. Usually you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests, but
looking a bit about the below three options (ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://github.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-intel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01org/liby
ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get started
to run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Charles, Daniel
2016-12-08 01:24:34 UTC
Permalink
That's not expected, libdrm should also compile ok on the defaults.
Normally what I see Ubuntu users do is to run $sudo make install

If you just want to install it on a custom folder, --prefix=<some_dir>
should be sufficient for all packages you listed, no need to mess up
with --exec-dir
--
Daniel.



On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm doesn’t build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the --exec-prefix=/ directories?
If you want to install it on the default place you don't need to specify those
--
Daniel.
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version 4.8.0 (default kernel that comes with Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
GEN intel_version.h
make all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
GEN frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
libva info: VA-API version 0.39.2
libva info: va_getDriverName() returns 0 libva info: Trying to open
/usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
VAProfileMPEG2Simple : VAEntrypointVLD
VAProfileMPEG2Simple : VAEntrypointEncSlice
VAProfileMPEG2Main : VAEntrypointVLD
VAProfileMPEG2Main : VAEntrypointEncSlice
VAProfileH264ConstrainedBaseline: VAEntrypointVLD
VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
VAProfileH264Main : VAEntrypointVLD
VAProfileH264Main : VAEntrypointEncSlice
VAProfileH264High : VAEntrypointVLD
VAProfileH264High : VAEntrypointEncSlice
VAProfileH264MultiviewHigh : VAEntrypointVLD
VAProfileH264MultiviewHigh : VAEntrypointEncSlice
VAProfileH264StereoHigh : VAEntrypointVLD
VAProfileH264StereoHigh : VAEntrypointEncSlice
VAProfileVC1Simple : VAEntrypointVLD
VAProfileVC1Main : VAEntrypointVLD
VAProfileVC1Advanced : VAEntrypointVLD
VAProfileNone : VAEntrypointVideoProc
VAProfileJPEGBaseline : VAEntrypointVLD
VAProfileJPEGBaseline : VAEntrypointEncPicture
VAProfileVP8Version0_3 : VAEntrypointVLD
VAProfileVP8Version0_3 : VAEntrypointEncSlice
VAProfileHEVCMain : VAEntrypointVLD
VAProfileHEVCMain : VAEntrypointEncSlice
VAProfileHEVCMain10 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointEncSlice
VAProfileVP9Profile2 : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel. The kernel in the specific Linux OS might not support Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you should check xf86-video-intel supports Kabylake or not. Usually you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests, but
looking a bit about the below three options (ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://github.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-intel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01org/liby
ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get started
to run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Vijayaraghavan, Vasavee
2016-12-08 02:13:13 UTC
Permalink
Hi Daniel,

That was right. I messed up a bit with the paths, uninstalling and then re-installing with the default path in configure worked fine this time.
Thanks!

-best Regards,
Vasavee


-----Original Message-----
From: Charles, Daniel [mailto:***@intel.com]
Sent: Wednesday, December 7, 2016 5:25 PM
To: Vijayaraghavan, Vasavee <***@intel.com>
Cc: Xiang, Haihao <***@intel.com>; ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake

That's not expected, libdrm should also compile ok on the defaults.
Normally what I see Ubuntu users do is to run $sudo make install

If you just want to install it on a custom folder, --prefix=<some_dir> should be sufficient for all packages you listed, no need to mess up with --exec-dir
--
Daniel.



On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm doesn’t build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the --exec-prefix=/ directories?
If you want to install it on the default place you don't need to specify those
--
Daniel.
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version 4.8.0 (default kernel that comes with Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
GEN intel_version.h
make all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
GEN frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
libva info: VA-API version 0.39.2
libva info: va_getDriverName() returns 0 libva info: Trying to open
/usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
VAProfileMPEG2Simple : VAEntrypointVLD
VAProfileMPEG2Simple : VAEntrypointEncSlice
VAProfileMPEG2Main : VAEntrypointVLD
VAProfileMPEG2Main : VAEntrypointEncSlice
VAProfileH264ConstrainedBaseline: VAEntrypointVLD
VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
VAProfileH264Main : VAEntrypointVLD
VAProfileH264Main : VAEntrypointEncSlice
VAProfileH264High : VAEntrypointVLD
VAProfileH264High : VAEntrypointEncSlice
VAProfileH264MultiviewHigh : VAEntrypointVLD
VAProfileH264MultiviewHigh : VAEntrypointEncSlice
VAProfileH264StereoHigh : VAEntrypointVLD
VAProfileH264StereoHigh : VAEntrypointEncSlice
VAProfileVC1Simple : VAEntrypointVLD
VAProfileVC1Main : VAEntrypointVLD
VAProfileVC1Advanced : VAEntrypointVLD
VAProfileNone : VAEntrypointVideoProc
VAProfileJPEGBaseline : VAEntrypointVLD
VAProfileJPEGBaseline : VAEntrypointEncPicture
VAProfileVP8Version0_3 : VAEntrypointVLD
VAProfileVP8Version0_3 : VAEntrypointEncSlice
VAProfileHEVCMain : VAEntrypointVLD
VAProfileHEVCMain : VAEntrypointEncSlice
VAProfileHEVCMain10 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointEncSlice
VAProfileVP9Profile2 : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel. The kernel in the specific Linux OS might not support Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you should check xf86-video-intel supports Kabylake or not. Usually you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests, but
looking a bit about the below three options (ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://github.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-intel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01org/liby
ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get started
to run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Xiang, Haihao
2016-12-08 04:06:50 UTC
Permalink
I think './configure --prefix=/usr --exec-prefix=/' should work too,
otherwise it might have issue. Actually this configuration works fine
for me when I build libva and libva-intel-driver. I set PKG_CONFIG_PATH
variable to /lib/pkgconfig because libva.pc is installed in
/lib/pkgconfig which is not in the default pkg-config search path.

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
That was right. I messed up a bit with the paths, uninstalling and
then re-installing with the default path in configure worked fine
this time.
Thanks!
-best Regards,
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 5:25 PM
rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
That's not expected, libdrm should also compile ok on the defaults.
Normally what I see Ubuntu users do is to run  $sudo make install
If you just want to install it on a custom folder, --
prefix=<some_dir> should be sufficient for all packages you listed,
no need to mess up with --exec-dir
--
Daniel.
On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm doesn’t
build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the --
exec-prefix=/ directories?
If you want to install it on the default place you don't need to specify those
--
Daniel.
On Wed, Dec 7, 2016 at 2:24 PM, Vijayaraghavan, Vasavee <vasavee.vi
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version  4.8.0 (default kernel that comes with
Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
I have error while trying to compile it (I used this for
all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
  GEN      intel_version.h
make  all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
  GEN      frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
libva info: VA-API version 0.39.2
libva info: va_getDriverName() returns 0 libva info: Trying to open
/usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
      VAProfileMPEG2Simple            : VAEntrypointVLD
      VAProfileMPEG2Simple            : VAEntrypointEncSlice
      VAProfileMPEG2Main              : VAEntrypointVLD
      VAProfileMPEG2Main              : VAEntrypointEncSlice
      VAProfileH264ConstrainedBaseline: VAEntrypointVLD
      VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
      VAProfileH264Main               : VAEntrypointVLD
      VAProfileH264Main               : VAEntrypointEncSlice
      VAProfileH264High               : VAEntrypointVLD
      VAProfileH264High               : VAEntrypointEncSlice
      VAProfileH264MultiviewHigh      : VAEntrypointVLD
      VAProfileH264MultiviewHigh      : VAEntrypointEncSlice
      VAProfileH264StereoHigh         : VAEntrypointVLD
      VAProfileH264StereoHigh         : VAEntrypointEncSlice
      VAProfileVC1Simple              : VAEntrypointVLD
      VAProfileVC1Main                : VAEntrypointVLD
      VAProfileVC1Advanced            : VAEntrypointVLD
      VAProfileNone                   : VAEntrypointVideoProc
      VAProfileJPEGBaseline           : VAEntrypointVLD
      VAProfileJPEGBaseline           : VAEntrypointEncPicture
      VAProfileVP8Version0_3          : VAEntrypointVLD
      VAProfileVP8Version0_3          : VAEntrypointEncSlice
      VAProfileHEVCMain               : VAEntrypointVLD
      VAProfileHEVCMain               : VAEntrypointEncSlice
      VAProfileHEVCMain10             : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointEncSlice
      VAProfileVP9Profile2            : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode
on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc
kernel. The kernel in the specific Linux OS might not support
Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you
should check xf86-video-intel supports Kabylake or not. Usually
you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it
would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests, but
looking a bit about the below three options (ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://github
.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
      Linux Kernel - 4.7.2
      Mesa - 12.0.1
      xf86-video-intel - 2.99.917
      Libdrm - 2.4.68
      Libva - 1.7.2
      vaapi intel-driver - 1.7.2
      Cairo - 1.15.2
      Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-i
ntel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode
on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01or
g/liby
ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get started
to run hardware accelerated encode/decode tests on KabyLake? I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Vijayaraghavan, Vasavee
2016-12-12 18:45:38 UTC
Permalink
Hi Haihao,

I might have missed setting the PKG_CONFIG_PATH while trying to use './configure --prefix=/usr --exec-prefix=/'.
But like Daniel suggested, I did a clean install with default paths and it works fine for me.

I have installed libyami and libyami utils to test VP9 encode and decode. I am able to run VP9 encode and decode using the pre-built binaries located in libyami-utils/tools (yamiencode and yamidecode).
I am facing issues in playing back the VP9 encoded video.
Say test.ivf is my VP9 encoded output, when I playback the file using ffplay or VLC player, I am able to see only the first and last frame of the encoded video (though the video shows to have 500 frames - same as the input yuv; verified the number of frames using ffprobe). Although, when I decode it back to yuv, the yuv is exactly the same as original input yuv and plays all the frames fine.

At this point, I haven’t added any quality control factor to encode the video and hence I have used a simple command line:
$cd /home/user/libyami-utils/tools
$./yamiencode -c VP9 -i input.yuv -W <> -H <> -s I420 -f 30 -N 500 -o test.ivf

Am I missing something in the commandline which is why I am unable to play the output?

Note: I tried playing pre-encoded test_vp9.ivf files available through MediaSDK samples and they played without an issue.

-Thanks
Vasavee

-----Original Message-----
From: Xiang, Haihao
Sent: Wednesday, December 7, 2016 8:07 PM
To: Charles, Daniel <***@intel.com>; Vijayaraghavan, Vasavee <***@intel.com>
Cc: ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake


I think './configure --prefix=/usr --exec-prefix=/' should work too, otherwise it might have issue. Actually this configuration works fine for me when I build libva and libva-intel-driver. I set PKG_CONFIG_PATH variable to /lib/pkgconfig because libva.pc is installed in /lib/pkgconfig which is not in the default pkg-config search path.

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
That was right. I messed up a bit with the paths, uninstalling and
then re-installing with the default path in configure worked fine this
time.
Thanks!
-best Regards,
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 5:25 PM
rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
That's not expected, libdrm should also compile ok on the defaults.
Normally what I see Ubuntu users do is to run  $sudo make install
If you just want to install it on a custom folder, --
prefix=<some_dir> should be sufficient for all packages you listed, no
need to mess up with --exec-dir
--
Daniel.
On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm doesn’t
build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the --
exec-prefix=/ directories?
If you want to install it on the default place you don't need to specify those
--
Daniel.
On Wed, Dec 7, 2016 at 2:24 PM, Vijayaraghavan, Vasavee <vasavee.vi
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version  4.8.0 (default kernel that comes with
Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
I have error while trying to compile it (I used this for
Making all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
  GEN      intel_version.h
make  all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
  GEN      frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
libva info: VA-API version 0.39.2
libva info: va_getDriverName() returns 0 libva info: Trying to
open /usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
      VAProfileMPEG2Simple            : VAEntrypointVLD
      VAProfileMPEG2Simple            : VAEntrypointEncSlice
      VAProfileMPEG2Main              : VAEntrypointVLD
      VAProfileMPEG2Main              : VAEntrypointEncSlice
      VAProfileH264ConstrainedBaseline: VAEntrypointVLD
      VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
      VAProfileH264Main               : VAEntrypointVLD
      VAProfileH264Main               : VAEntrypointEncSlice
      VAProfileH264High               : VAEntrypointVLD
      VAProfileH264High               : VAEntrypointEncSlice
      VAProfileH264MultiviewHigh      : VAEntrypointVLD
      VAProfileH264MultiviewHigh      : VAEntrypointEncSlice
      VAProfileH264StereoHigh         : VAEntrypointVLD
      VAProfileH264StereoHigh         : VAEntrypointEncSlice
      VAProfileVC1Simple              : VAEntrypointVLD
      VAProfileVC1Main                : VAEntrypointVLD
      VAProfileVC1Advanced            : VAEntrypointVLD
      VAProfileNone                   : VAEntrypointVideoProc
      VAProfileJPEGBaseline           : VAEntrypointVLD
      VAProfileJPEGBaseline           : VAEntrypointEncPicture
      VAProfileVP8Version0_3          : VAEntrypointVLD
      VAProfileVP8Version0_3          : VAEntrypointEncSlice
      VAProfileHEVCMain               : VAEntrypointVLD
      VAProfileHEVCMain               : VAEntrypointEncSlice
      VAProfileHEVCMain10             : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointEncSlice
      VAProfileVP9Profile2            : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel.
The kernel in the specific Linux OS might not support Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you
should check xf86-video-intel supports Kabylake or not. Usually
you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it
would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests,
but looking a bit about the below three options (ffmpeg,
gstreamer and
1. Simply Follow the build procedure given here: https://github
.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
      Linux Kernel - 4.7.2
      Mesa - 12.0.1
      xf86-video-intel - 2.99.917
      Libdrm - 2.4.68
      Libva - 1.7.2
      vaapi intel-driver - 1.7.2
      Cairo - 1.15.2
      Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-i
ntel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01or
g/liby ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get
started to run hardware accelerated encode/decode tests on
KabyLake?
I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Charles, Daniel
2016-12-12 18:52:38 UTC
Permalink
Hi Vasavee,

Can you file a bug on libyami for your observation?

https://github.com/01org/libyami/issues

Thanks.
--
Daniel.

On Mon, Dec 12, 2016 at 10:45 AM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Haihao,
I might have missed setting the PKG_CONFIG_PATH while trying to use './configure --prefix=/usr --exec-prefix=/'.
But like Daniel suggested, I did a clean install with default paths and it works fine for me.
I have installed libyami and libyami utils to test VP9 encode and decode. I am able to run VP9 encode and decode using the pre-built binaries located in libyami-utils/tools (yamiencode and yamidecode).
I am facing issues in playing back the VP9 encoded video.
Say test.ivf is my VP9 encoded output, when I playback the file using ffplay or VLC player, I am able to see only the first and last frame of the encoded video (though the video shows to have 500 frames - same as the input yuv; verified the number of frames using ffprobe). Although, when I decode it back to yuv, the yuv is exactly the same as original input yuv and plays all the frames fine.
$cd /home/user/libyami-utils/tools
$./yamiencode -c VP9 -i input.yuv -W <> -H <> -s I420 -f 30 -N 500 -o test.ivf
Am I missing something in the commandline which is why I am unable to play the output?
Note: I tried playing pre-encoded test_vp9.ivf files available through MediaSDK samples and they played without an issue.
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Wednesday, December 7, 2016 8:07 PM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
I think './configure --prefix=/usr --exec-prefix=/' should work too, otherwise it might have issue. Actually this configuration works fine for me when I build libva and libva-intel-driver. I set PKG_CONFIG_PATH variable to /lib/pkgconfig because libva.pc is installed in /lib/pkgconfig which is not in the default pkg-config search path.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
That was right. I messed up a bit with the paths, uninstalling and
then re-installing with the default path in configure worked fine this
time.
Thanks!
-best Regards,
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 5:25 PM
rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
That's not expected, libdrm should also compile ok on the defaults.
Normally what I see Ubuntu users do is to run $sudo make install
If you just want to install it on a custom folder, --
prefix=<some_dir> should be sufficient for all packages you listed, no
need to mess up with --exec-dir
--
Daniel.
On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm doesn’t
build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the --
exec-prefix=/ directories?
If you want to install it on the default place you don't need to specify those
--
Daniel.
On Wed, Dec 7, 2016 at 2:24 PM, Vijayaraghavan, Vasavee <vasavee.vi
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version 4.8.0 (default kernel that comes with Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
I have error while trying to compile it (I used this for
Making all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
GEN intel_version.h
make all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
GEN frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
libva info: VA-API version 0.39.2
libva info: va_getDriverName() returns 0 libva info: Trying to
open /usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
VAProfileMPEG2Simple : VAEntrypointVLD
VAProfileMPEG2Simple : VAEntrypointEncSlice
VAProfileMPEG2Main : VAEntrypointVLD
VAProfileMPEG2Main : VAEntrypointEncSlice
VAProfileH264ConstrainedBaseline: VAEntrypointVLD
VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
VAProfileH264Main : VAEntrypointVLD
VAProfileH264Main : VAEntrypointEncSlice
VAProfileH264High : VAEntrypointVLD
VAProfileH264High : VAEntrypointEncSlice
VAProfileH264MultiviewHigh : VAEntrypointVLD
VAProfileH264MultiviewHigh : VAEntrypointEncSlice
VAProfileH264StereoHigh : VAEntrypointVLD
VAProfileH264StereoHigh : VAEntrypointEncSlice
VAProfileVC1Simple : VAEntrypointVLD
VAProfileVC1Main : VAEntrypointVLD
VAProfileVC1Advanced : VAEntrypointVLD
VAProfileNone : VAEntrypointVideoProc
VAProfileJPEGBaseline : VAEntrypointVLD
VAProfileJPEGBaseline : VAEntrypointEncPicture
VAProfileVP8Version0_3 : VAEntrypointVLD
VAProfileVP8Version0_3 : VAEntrypointEncSlice
VAProfileHEVCMain : VAEntrypointVLD
VAProfileHEVCMain : VAEntrypointEncSlice
VAProfileHEVCMain10 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointEncSlice
VAProfileVP9Profile2 : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel.
The kernel in the specific Linux OS might not support Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you
should check xf86-video-intel supports Kabylake or not. Usually
you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it
would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my tests,
but looking a bit about the below three options (ffmpeg,
gstreamer and
1. Simply Follow the build procedure given here: https://github
.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-i
ntel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01or
g/liby ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get
started to run hardware accelerated encode/decode tests on
KabyLake?
I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Vijayaraghavan, Vasavee
2016-12-12 19:58:11 UTC
Permalink
Hi Daniel,

Sure, will do that! Thank you for the pointers.

-Best Regards,
Vasavee

-----Original Message-----
From: Charles, Daniel [mailto:***@intel.com]
Sent: Monday, December 12, 2016 10:53 AM
To: Vijayaraghavan, Vasavee <***@intel.com>
Cc: Xiang, Haihao <***@intel.com>; ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake

Hi Vasavee,

Can you file a bug on libyami for your observation?

https://github.com/01org/libyami/issues

Thanks.
--
Daniel.
Post by Vijayaraghavan, Vasavee
Hi Haihao,
I might have missed setting the PKG_CONFIG_PATH while trying to use './configure --prefix=/usr --exec-prefix=/'.
But like Daniel suggested, I did a clean install with default paths and it works fine for me.
I have installed libyami and libyami utils to test VP9 encode and decode. I am able to run VP9 encode and decode using the pre-built binaries located in libyami-utils/tools (yamiencode and yamidecode).
I am facing issues in playing back the VP9 encoded video.
Say test.ivf is my VP9 encoded output, when I playback the file using ffplay or VLC player, I am able to see only the first and last frame of the encoded video (though the video shows to have 500 frames - same as the input yuv; verified the number of frames using ffprobe). Although, when I decode it back to yuv, the yuv is exactly the same as original input yuv and plays all the frames fine.
$cd /home/user/libyami-utils/tools
$./yamiencode -c VP9 -i input.yuv -W <> -H <> -s I420 -f 30 -N 500 -o test.ivf
Am I missing something in the commandline which is why I am unable to play the output?
Note: I tried playing pre-encoded test_vp9.ivf files available through MediaSDK samples and they played without an issue.
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Wednesday, December 7, 2016 8:07 PM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
I think './configure --prefix=/usr --exec-prefix=/' should work too, otherwise it might have issue. Actually this configuration works fine for me when I build libva and libva-intel-driver. I set PKG_CONFIG_PATH variable to /lib/pkgconfig because libva.pc is installed in /lib/pkgconfig which is not in the default pkg-config search path.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
That was right. I messed up a bit with the paths, uninstalling and
then re-installing with the default path in configure worked fine
this time.
Thanks!
-best Regards,
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 5:25 PM
rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
That's not expected, libdrm should also compile ok on the defaults.
Normally what I see Ubuntu users do is to run $sudo make install
If you just want to install it on a custom folder, --
prefix=<some_dir> should be sufficient for all packages you listed,
no need to mess up with --exec-dir
--
Daniel.
On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm doesn’t
build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the --
exec-prefix=/ directories?
If you want to install it on the default place you don't need to specify those
--
Daniel.
On Wed, Dec 7, 2016 at 2:24 PM, Vijayaraghavan, Vasavee <vasavee.vi
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version 4.8.0 (default kernel that comes with Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
I have error while trying to compile it (I used this for
Making all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
GEN intel_version.h
make all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
GEN frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
libva info: VA-API version 0.39.2 libva info: va_getDriverName()
returns 0 libva info: Trying to open
/usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R) Kabylake - 1.7.1
vainfo: Supported profile and entrypoints
VAProfileMPEG2Simple : VAEntrypointVLD
VAProfileMPEG2Simple : VAEntrypointEncSlice
VAProfileMPEG2Main : VAEntrypointVLD
VAProfileMPEG2Main : VAEntrypointEncSlice
VAProfileH264ConstrainedBaseline: VAEntrypointVLD
VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
VAProfileH264Main : VAEntrypointVLD
VAProfileH264Main : VAEntrypointEncSlice
VAProfileH264High : VAEntrypointVLD
VAProfileH264High : VAEntrypointEncSlice
VAProfileH264MultiviewHigh : VAEntrypointVLD
VAProfileH264MultiviewHigh : VAEntrypointEncSlice
VAProfileH264StereoHigh : VAEntrypointVLD
VAProfileH264StereoHigh : VAEntrypointEncSlice
VAProfileVC1Simple : VAEntrypointVLD
VAProfileVC1Main : VAEntrypointVLD
VAProfileVC1Advanced : VAEntrypointVLD
VAProfileNone : VAEntrypointVideoProc
VAProfileJPEGBaseline : VAEntrypointVLD
VAProfileJPEGBaseline : VAEntrypointEncPicture
VAProfileVP8Version0_3 : VAEntrypointVLD
VAProfileVP8Version0_3 : VAEntrypointEncSlice
VAProfileHEVCMain : VAEntrypointVLD
VAProfileHEVCMain : VAEntrypointEncSlice
VAProfileHEVCMain10 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointVLD
VAProfileVP9Profile0 : VAEntrypointEncSlice
VAProfileVP9Profile2 : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel.
The kernel in the specific Linux OS might not support Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you
should check xf86-video-intel supports Kabylake or not. Usually
you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it
would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my
tests, but looking a bit about the below three options (ffmpeg,
gstreamer and
1. Simply Follow the build procedure given here: https://github
.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
Linux Kernel - 4.7.2
Mesa - 12.0.1
xf86-video-intel - 2.99.917
Libdrm - 2.4.68
Libva - 1.7.2
vaapi intel-driver - 1.7.2
Cairo - 1.15.2
Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016q3-i
ntel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/01or
g/liby ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.html
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on KabyLake.
Can someone give me useful pointers as in where I can get
started to run hardware accelerated encode/decode tests on
KabyLake?
I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Xiang, Haihao
2016-12-15 08:08:29 UTC
Permalink
Hi Vasavee,

Maybe it is not a yami issue. I encountered another issue for VP8
 video which is encoded by another vaapi based tool. I saw double
frames when transcoding the video back to YUV using ffmpeg, however
vpxdec works well for me, so I guess there are some issues in FFmpeg.
Could you try vpxdec with your VP9 video? I think it is not yami issue
if vpxdec works for you.

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
Sure, will do that! Thank you for the pointers.
-Best Regards,
Vasavee
-----Original Message-----
Sent: Monday, December 12, 2016 10:53 AM
rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
Can you file a bug on libyami for your observation?
https://github.com/01org/libyami/issues
Thanks.
--
Daniel.
On Mon, Dec 12, 2016 at 10:45 AM, Vijayaraghavan, Vasavee <vasavee.vi
Post by Vijayaraghavan, Vasavee
Hi Haihao,
I might have missed setting the PKG_CONFIG_PATH while trying to use
'./configure --prefix=/usr --exec-prefix=/'.
But like Daniel suggested, I did a clean install with default paths
and it works fine for me.
I have installed libyami and libyami utils to test VP9 encode and
decode. I am able to run VP9 encode and decode using the pre-built
binaries located in libyami-utils/tools (yamiencode and
yamidecode).
I am facing issues in playing back the VP9 encoded video.
Say test.ivf is my VP9 encoded output, when I playback the file
using ffplay or VLC player, I am able to see only the first and
last frame of the encoded video (though the video shows to have 500
frames - same as the input yuv; verified the number of frames using
ffprobe). Although, when I decode it back to yuv, the yuv is
exactly the same as original input yuv and plays all the frames
fine.
At this point, I haven’t added any quality control factor to encode
$cd /home/user/libyami-utils/tools
$./yamiencode -c VP9 -i input.yuv -W <> -H <> -s I420 -f 30 -N 500
-o
test.ivf
Am I missing something in the commandline which is why I am unable to play the output?
Note: I tried playing pre-encoded test_vp9.ivf files available
through MediaSDK samples and they played without an issue.
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Wednesday, December 7, 2016 8:07 PM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode
on KabyLake
I think './configure --prefix=/usr --exec-prefix=/' should work
too, otherwise it might have issue. Actually this configuration
works fine for me when I build libva and libva-intel-driver. I set
PKG_CONFIG_PATH variable to /lib/pkgconfig because libva.pc is
installed in /lib/pkgconfig which is not in the default pkg-config
search path.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
That was right. I messed up a bit with the paths, uninstalling and
then re-installing with the default path in configure worked fine
this time.
Thanks!
-best Regards,
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 5:25 PM
op.o
rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode
on KabyLake
That's not expected, libdrm should also compile ok on the
defaults.
Normally what I see Ubuntu users do is to run  $sudo make install
If you just want to install it on a custom folder, --
prefix=<some_dir> should be sufficient for all packages you listed,
no need to mess up with --exec-dir
--
Daniel.
On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm doesn’t
build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
ktop
.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the --
exec-prefix=/ directories?
If you want to install it on the default place you don't need
to
specify those
--
Daniel.
On Wed, Dec 7, 2016 at 2:24 PM, Vijayaraghavan, Vasavee
<vasavee.vi
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version  4.8.0 (default kernel that comes with
Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
Making all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src'
  GEN      intel_version.h
make  all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/mpeg2/vld'
  GEN      frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
va_getDriverName()
returns 0 libva info: Trying to open
/usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R)
Kabylake -
1.7.1
vainfo: Supported profile and entrypoints
      VAProfileMPEG2Simple            : VAEntrypointVLD
      VAProfileMPEG2Simple            : VAEntrypointEncSlice
      VAProfileMPEG2Main              : VAEntrypointVLD
      VAProfileMPEG2Main              : VAEntrypointEncSlice
      VAProfileH264ConstrainedBaseline: VAEntrypointVLD
      VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
      VAProfileH264Main               : VAEntrypointVLD
      VAProfileH264Main               : VAEntrypointEncSlice
      VAProfileH264High               : VAEntrypointVLD
      VAProfileH264High               : VAEntrypointEncSlice
      VAProfileH264MultiviewHigh      : VAEntrypointVLD
      VAProfileH264MultiviewHigh      : VAEntrypointEncSlice
      VAProfileH264StereoHigh         : VAEntrypointVLD
      VAProfileH264StereoHigh         : VAEntrypointEncSlice
      VAProfileVC1Simple              : VAEntrypointVLD
      VAProfileVC1Main                : VAEntrypointVLD
      VAProfileVC1Advanced            : VAEntrypointVLD
      VAProfileNone                   : VAEntrypointVideoProc
      VAProfileJPEGBaseline           : VAEntrypointVLD
VAEntrypointEncPicture
      VAProfileVP8Version0_3          : VAEntrypointVLD
      VAProfileVP8Version0_3          : VAEntrypointEncSlice
      VAProfileHEVCMain               : VAEntrypointVLD
      VAProfileHEVCMain               : VAEntrypointEncSlice
      VAProfileHEVCMain10             : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointEncSlice
      VAProfileVP9Profile2            : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Post by Vijayaraghavan, Vasavee
;
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel.
The kernel in the specific Linux OS might not support
Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you
should check xf86-video-intel supports Kabylake or not. Usually
you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so it
would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Sorry, didn’t realize I had to reply all. Reposting my
message
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my
tests, but looking a bit about the below three options (ffmpeg,
gstreamer and
1. Simply Follow the build procedure given here: https://gi
thub
.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack after
      Linux Kernel - 4.7.2
      Mesa - 12.0.1
      xf86-video-intel - 2.99.917
      Libdrm - 2.4.68
      Libva - 1.7.2
      vaapi intel-driver - 1.7.2
      Cairo - 1.15.2
      Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016
q3-i
ntel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
om>;
libva
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9
hardware
https://github.com/01org/libyami (core) https://github.com/
01or
g/liby ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.h
tml
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode on
KabyLake.
Can someone give me useful pointers as in where I can get
started to run hardware accelerated encode/decode tests on
KabyLake?
I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Vijayaraghavan, Vasavee
2016-12-15 18:01:54 UTC
Permalink
Hi Haihao,

I think I mislead you by not stating the problem correctly, sorry about that! I will rephrase the issue that I am facing:

- OTC graphics stack (Ubuntu 16.10 (kernel 4.8), libdrm 2.4.68, libva 1.7.2 and libyami/libyami-utils)
- Command line used for encode:
./yamiencode -c VP9 -i input.yuv -W <> -H <> -s I420 -f 30 -N 500 -o output.ivf (or output.webm)

I wanted to play the output.ivf (output.webm) file to verify whether it was encoded properly. Tried looking at the encoded output using ffplay/ VLC/ Dragging and dropping in chrome browser
I am unable to view this encoded video completely (able to see only first and last frame of the video - chrome browser is not able to play the video even for the first and last frames)

On the other hand, decoding this output.ivf (/output.webm) back to yuv doesn’t give any issue to me. The decoded yuv plays back fine and looks similar to the original input yuv that I have used.
Also, I did not use ffmpeg for anything but just for using the player (ffplay) so I assume the issue is not related to ffmpeg in my case.

-Thanks
Vasavee


-----Original Message-----
From: Xiang, Haihao
Sent: Thursday, December 15, 2016 12:08 AM
To: Charles, Daniel <***@intel.com>; Vijayaraghavan, Vasavee <***@intel.com>
Cc: ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake


Hi Vasavee,

Maybe it is not a yami issue. I encountered another issue for VP8
 video which is encoded by another vaapi based tool. I saw double frames when transcoding the video back to YUV using ffmpeg, however vpxdec works well for me, so I guess there are some issues in FFmpeg.
Could you try vpxdec with your VP9 video? I think it is not yami issue if vpxdec works for you.

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
Sure, will do that! Thank you for the pointers.
-Best Regards,
Vasavee
-----Original Message-----
Sent: Monday, December 12, 2016 10:53 AM
rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
Can you file a bug on libyami for your observation?
https://github.com/01org/libyami/issues
Thanks.
--
Daniel.
On Mon, Dec 12, 2016 at 10:45 AM, Vijayaraghavan, Vasavee <vasavee.vi
Post by Vijayaraghavan, Vasavee
Hi Haihao,
I might have missed setting the PKG_CONFIG_PATH while trying to use
'./configure --prefix=/usr --exec-prefix=/'.
But like Daniel suggested, I did a clean install with default paths
and it works fine for me.
I have installed libyami and libyami utils to test VP9 encode and
decode. I am able to run VP9 encode and decode using the pre-built
binaries located in libyami-utils/tools (yamiencode and yamidecode).
I am facing issues in playing back the VP9 encoded video.
Say test.ivf is my VP9 encoded output, when I playback the file
using ffplay or VLC player, I am able to see only the first and last
frame of the encoded video (though the video shows to have 500
frames - same as the input yuv; verified the number of frames using
ffprobe). Although, when I decode it back to yuv, the yuv is exactly
the same as original input yuv and plays all the frames fine.
At this point, I haven’t added any quality control factor to encode
$cd /home/user/libyami-utils/tools
$./yamiencode -c VP9 -i input.yuv -W <> -H <> -s I420 -f 30 -N 500 -o test.ivf
Am I missing something in the commandline which is why I am unable to play the output?
Note: I tried playing pre-encoded test_vp9.ivf files available
through MediaSDK samples and they played without an issue.
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Wednesday, December 7, 2016 8:07 PM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
I think './configure --prefix=/usr --exec-prefix=/' should work too,
otherwise it might have issue. Actually this configuration works
fine for me when I build libva and libva-intel-driver. I set
PKG_CONFIG_PATH variable to /lib/pkgconfig because libva.pc is
installed in /lib/pkgconfig which is not in the default pkg-config
search path.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
That was right. I messed up a bit with the paths, uninstalling and
then re-installing with the default path in configure worked fine
this time.
Thanks!
-best Regards,
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 5:25 PM
op.o rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
That's not expected, libdrm should also compile ok on the
defaults.
Normally what I see Ubuntu users do is to run  $sudo make install
If you just want to install it on a custom folder, --
prefix=<some_dir> should be sufficient for all packages you
listed, no need to mess up with --exec-dir
--
Daniel.
On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm
doesn’t build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
ktop .org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the
-- exec-prefix=/ directories?
If you want to install it on the default place you don't need to specify those
--
Daniel.
On Wed, Dec 7, 2016 at 2:24 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version  4.8.0 (default kernel that comes with
Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
Making all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src'
  GEN      intel_version.h
make  all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/mpeg2/vld'
  GEN      frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
va_getDriverName()
returns 0 libva info: Trying to open
/usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R)
Kabylake -
1.7.1
vainfo: Supported profile and entrypoints
      VAProfileMPEG2Simple            : VAEntrypointVLD
      VAProfileMPEG2Simple            : VAEntrypointEncSlice
      VAProfileMPEG2Main              : VAEntrypointVLD
      VAProfileMPEG2Main              : VAEntrypointEncSlice
      VAProfileH264ConstrainedBaseline: VAEntrypointVLD
      VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
      VAProfileH264Main               : VAEntrypointVLD
      VAProfileH264Main               : VAEntrypointEncSlice
      VAProfileH264High               : VAEntrypointVLD
      VAProfileH264High               : VAEntrypointEncSlice
      VAProfileH264MultiviewHigh      : VAEntrypointVLD
      VAProfileH264MultiviewHigh      : VAEntrypointEncSlice
      VAProfileH264StereoHigh         : VAEntrypointVLD
      VAProfileH264StereoHigh         : VAEntrypointEncSlice
      VAProfileVC1Simple              : VAEntrypointVLD
      VAProfileVC1Main                : VAEntrypointVLD
      VAProfileVC1Advanced            : VAEntrypointVLD
      VAProfileNone                   : VAEntrypointVideoProc
      VAProfileJPEGBaseline           : VAEntrypointVLD
VAEntrypointEncPicture
      VAProfileVP8Version0_3          : VAEntrypointVLD
      VAProfileVP8Version0_3          : VAEntrypointEncSlice
      VAProfileHEVCMain               : VAEntrypointVLD
      VAProfileHEVCMain               : VAEntrypointEncSlice
      VAProfileHEVCMain10             : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointEncSlice
      VAProfileVP9Profile2            : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Post by Vijayaraghavan, Vasavee
;
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel.
The kernel in the specific Linux OS might not support
Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you
should check xf86-video-intel supports Kabylake or not. Usually
you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so
it would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Sorry, didn’t realize I had to reply all. Reposting my
message
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my
tests, but looking a bit about the below three options
(ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://gi
thub
.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack
      Linux Kernel - 4.7.2
      Mesa - 12.0.1
      xf86-video-intel - 2.99.917
      Libdrm - 2.4.68
      Libva - 1.7.2
      vaapi intel-driver - 1.7.2
      Cairo - 1.15.2
      Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016
q3-i
ntel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
om>;
libva
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/
01or g/liby ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.h
tml
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode
on KabyLake.
Can someone give me useful pointers as in where I can get
started to run hardware accelerated encode/decode tests on
KabyLake?
I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
Tank, Jayesh KumarX
2016-12-15 18:59:18 UTC
Permalink
Hi Vasavee,
.ivf format is not the same as .webm

https://wiki.multimedia.cx/index.php?title=IVF

yamiencode does not output in webm format.

Hope it helps.

Thanks,
Jayesh Kumar

-----Original Message-----
From: Libva [mailto:libva-***@lists.freedesktop.org] On Behalf Of Vijayaraghavan, Vasavee
Sent: Thursday, December 15, 2016 10:02 AM
To: Xiang, Haihao <***@intel.com>; Charles, Daniel <***@intel.com>
Cc: ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake

Hi Haihao,

I think I mislead you by not stating the problem correctly, sorry about that! I will rephrase the issue that I am facing:

- OTC graphics stack (Ubuntu 16.10 (kernel 4.8), libdrm 2.4.68, libva 1.7.2 and libyami/libyami-utils)
- Command line used for encode:
./yamiencode -c VP9 -i input.yuv -W <> -H <> -s I420 -f 30 -N 500 -o output.ivf (or output.webm)

I wanted to play the output.ivf (output.webm) file to verify whether it was encoded properly. Tried looking at the encoded output using ffplay/ VLC/ Dragging and dropping in chrome browser I am unable to view this encoded video completely (able to see only first and last frame of the video - chrome browser is not able to play the video even for the first and last frames)

On the other hand, decoding this output.ivf (/output.webm) back to yuv doesn’t give any issue to me. The decoded yuv plays back fine and looks similar to the original input yuv that I have used.
Also, I did not use ffmpeg for anything but just for using the player (ffplay) so I assume the issue is not related to ffmpeg in my case.

-Thanks
Vasavee


-----Original Message-----
From: Xiang, Haihao
Sent: Thursday, December 15, 2016 12:08 AM
To: Charles, Daniel <***@intel.com>; Vijayaraghavan, Vasavee <***@intel.com>
Cc: ***@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake


Hi Vasavee,

Maybe it is not a yami issue. I encountered another issue for VP8
 video which is encoded by another vaapi based tool. I saw double frames when transcoding the video back to YUV using ffmpeg, however vpxdec works well for me, so I guess there are some issues in FFmpeg.
Could you try vpxdec with your VP9 video? I think it is not yami issue if vpxdec works for you.

Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
Sure, will do that! Thank you for the pointers.
-Best Regards,
Vasavee
-----Original Message-----
Sent: Monday, December 12, 2016 10:53 AM
rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
Hi Vasavee,
Can you file a bug on libyami for your observation?
https://github.com/01org/libyami/issues
Thanks.
--
Daniel.
On Mon, Dec 12, 2016 at 10:45 AM, Vijayaraghavan, Vasavee <vasavee.vi
Post by Vijayaraghavan, Vasavee
Hi Haihao,
I might have missed setting the PKG_CONFIG_PATH while trying to use
'./configure --prefix=/usr --exec-prefix=/'.
But like Daniel suggested, I did a clean install with default paths
and it works fine for me.
I have installed libyami and libyami utils to test VP9 encode and
decode. I am able to run VP9 encode and decode using the pre-built
binaries located in libyami-utils/tools (yamiencode and yamidecode).
I am facing issues in playing back the VP9 encoded video.
Say test.ivf is my VP9 encoded output, when I playback the file
using ffplay or VLC player, I am able to see only the first and last
frame of the encoded video (though the video shows to have 500
frames - same as the input yuv; verified the number of frames using
ffprobe). Although, when I decode it back to yuv, the yuv is exactly
the same as original input yuv and plays all the frames fine.
At this point, I haven’t added any quality control factor to encode
$cd /home/user/libyami-utils/tools
$./yamiencode -c VP9 -i input.yuv -W <> -H <> -s I420 -f 30 -N 500 -o test.ivf
Am I missing something in the commandline which is why I am unable to play the output?
Note: I tried playing pre-encoded test_vp9.ivf files available
through MediaSDK samples and they played without an issue.
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Wednesday, December 7, 2016 8:07 PM
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated encode/decode on KabyLake
I think './configure --prefix=/usr --exec-prefix=/' should work too,
otherwise it might have issue. Actually this configuration works
fine for me when I build libva and libva-intel-driver. I set
PKG_CONFIG_PATH variable to /lib/pkgconfig because libva.pc is
installed in /lib/pkgconfig which is not in the default pkg-config
search path.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi Daniel,
That was right. I messed up a bit with the paths, uninstalling and
then re-installing with the default path in configure worked fine
this time.
Thanks!
-best Regards,
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 5:25 PM
op.o rg
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
That's not expected, libdrm should also compile ok on the
defaults.
Normally what I see Ubuntu users do is to run  $sudo make install
If you just want to install it on a custom folder, --
prefix=<some_dir> should be sufficient for all packages you
listed, no need to mess up with --exec-dir
--
Daniel.
On Wed, Dec 7, 2016 at 5:07 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Daniel.
I believe so, I used this configuration because my libdrm
doesn’t build if I use the default config options.
-Thanks
Vasavee
-----Original Message-----
Sent: Wednesday, December 7, 2016 3:36 PM
ktop .org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hello Vasavee,
Is your user allowed to write files on the --prefix=/usr and the
-- exec-prefix=/ directories?
If you want to install it on the default place you don't need to specify those
--
Daniel.
On Wed, Dec 7, 2016 at 2:24 PM, Vijayaraghavan, Vasavee
Post by Vijayaraghavan, Vasavee
Hi Haihao,
-linux kernel version  4.8.0 (default kernel that comes with
Ubuntu
16.10) -libdrm version 2.4.68 -libva version 1.7.3
I am having trouble upgrading the libva-intel-driver-1.7.3.
Making all in debian.upstream
make[1]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/debian.upstream'
make[1]: Nothing to be done for 'all'.
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/debian.upstream'
Making all in src
make[1]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src'
  GEN      intel_version.h
make  all-recursive
make[2]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src'
Making all in shaders
make[3]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders'
Making all in h264
make[4]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264'
Making all in ildb
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264/ildb'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/ildb'
Making all in mc
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Nothing to be done for 'all'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264/mc'
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/h264'
make[5]: Nothing to be done for 'all-am'.
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/h264'
Making all in mpeg2
make[4]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/mpeg2'
Making all in vld
make[5]: Entering directory '/home/user/Downloads/libva-
intel-
driver-1.7.3/src/shaders/mpeg2/vld'
  GEN      frame_intra.g4b
frame_intra.g4s: 1: syntax error at ""
Makefile:560: recipe for target 'frame_intra.g4b' failed
make[5]: *** [frame_intra.g4b] Error 1
make[5]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2/vld'
Makefile:366: recipe for target 'all-recursive' failed
make[4]: *** [all-recursive] Error 1
make[4]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders/mpeg2'
Makefile:367: recipe for target 'all-recursive' failed
make[3]: *** [all-recursive] Error 1
make[3]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src/shaders'
Makefile:1170: recipe for target 'all-recursive' failed
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:595: recipe for target 'all' failed
make[1]: *** [all] Error 2
make[1]: Leaving directory '/home/user/Downloads/libva-intel-
driver-1.7.3/src'
Makefile:403: recipe for target 'all-recursive' failed
make: *** [all-recursive] Error 1
va_getDriverName()
returns 0 libva info: Trying to open
/usr/lib/x86_64-linux-gnu/dri/i965_drv_video.so
va_openDriver() returns 0
vainfo: VA-API version: 0.39 (libva 1.7.3)
vainfo: Driver version: Intel i965 driver for Intel(R)
Kabylake -
1.7.1
vainfo: Supported profile and entrypoints
      VAProfileMPEG2Simple            : VAEntrypointVLD
      VAProfileMPEG2Simple            : VAEntrypointEncSlice
      VAProfileMPEG2Main              : VAEntrypointVLD
      VAProfileMPEG2Main              : VAEntrypointEncSlice
      VAProfileH264ConstrainedBaseline: VAEntrypointVLD
      VAProfileH264ConstrainedBaseline: VAEntrypointEncSlice
      VAProfileH264Main               : VAEntrypointVLD
      VAProfileH264Main               : VAEntrypointEncSlice
      VAProfileH264High               : VAEntrypointVLD
      VAProfileH264High               : VAEntrypointEncSlice
      VAProfileH264MultiviewHigh      : VAEntrypointVLD
      VAProfileH264MultiviewHigh      : VAEntrypointEncSlice
      VAProfileH264StereoHigh         : VAEntrypointVLD
      VAProfileH264StereoHigh         : VAEntrypointEncSlice
      VAProfileVC1Simple              : VAEntrypointVLD
      VAProfileVC1Main                : VAEntrypointVLD
      VAProfileVC1Advanced            : VAEntrypointVLD
      VAProfileNone                   : VAEntrypointVideoProc
      VAProfileJPEGBaseline           : VAEntrypointVLD
VAEntrypointEncPicture
      VAProfileVP8Version0_3          : VAEntrypointVLD
      VAProfileVP8Version0_3          : VAEntrypointEncSlice
      VAProfileHEVCMain               : VAEntrypointVLD
      VAProfileHEVCMain               : VAEntrypointEncSlice
      VAProfileHEVCMain10             : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointVLD
      VAProfileVP9Profile0            : VAEntrypointEncSlice
      VAProfileVP9Profile2            : VAEntrypointVLD
-Thanks
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Tuesday, November 29, 2016 12:12 AM
Post by Vijayaraghavan, Vasavee
;
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
1. Linux kernel
It would be better to install a recent stable kernel or rc kernel.
The kernel in the specific Linux OS might not support
Kabylake.
2. Mesa/Cairo
It is not needed.
3. Xorg / xf86-video-intel
It is not needed if you won't playback a video, otherwise you
should check xf86-video-intel supports Kabylake or not. Usually
you needn't update Xorg.
4. libdrm
libdrm in the specific Linux OS might not support Kabylake, so
it would be better to install a recent version of libdrm.
5. libva/libva-intel-driver
The latest version is 1.7.3
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Sorry, didn’t realize I had to reply all. Reposting my
message
Hi Haihao,
Thank you for your response.
I am not sure if I have to use a specific software for my
tests, but looking a bit about the below three options
(ffmpeg, gstreamer and
1. Simply Follow the build procedure given here: https://gi
thub
.com/0
1org/libyami/wiki/Build after installing the specific Linux OS
(Or)
2. Do I have to build the entire graphics software stack
      Linux Kernel - 4.7.2
      Mesa - 12.0.1
      xf86-video-intel - 2.99.917
      Libdrm - 2.4.68
      Libva - 1.7.2
      vaapi intel-driver - 1.7.2
      Cairo - 1.15.2
      Xorg Xserver - 1.18.3
as mentioned in https://01.org/linuxgraphics/downloads/2016
q3-i
ntel-g
raphics-stack-release
-Best Regards,
Vasavee
-----Original Message-----
From: Xiang, Haihao
Sent: Monday, November 28, 2016 8:16 PM
om>;
libva
@lists.freedesktop.org
Subject: Re: [Libva] Evaluate VP9 Hardware accelerated
encode/decode on KabyLake
Hi Vasavee,
You can run a software using VA-API to evaluate VP9 hardware
https://github.com/01org/libyami (core) https://github.com/
01or g/liby ami-utils (utilities based on libyami)
gstreamer-vaapi
https://gstreamer.freedesktop.org/modules/gstreamer-vaapi.h
tml
or a FFmpeg/Libav based player which enables HW accelerated decode.
Thanks
Haihao
Post by Vijayaraghavan, Vasavee
Hi all,
I am new to this subscription list.
I want to evaluate VP9 hardware accelerated encode/decode
on KabyLake.
Can someone give me useful pointers as in where I can get
started to run hardware accelerated encode/decode tests on
KabyLake?
I am
targeting to run the tests on Linux OS.
Best Regards,
Vasavee
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
https://lists.freedesktop.org/mailman/listinfo/libva
_______________________________________________
Libva mailing list
***@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/libva

Loading...